Family-owned · Trusted by Port St. Lucie homeowners
4.7★(348+ Verified Reviews)
BBB
A+ Rated & Accredited
Angi
Super Service / Top Rated
Thumbtack
Top Pro
Nextdoor
Neighborhood Favorite
Licensed & Insured
Local Technicians
Licensed LG dryer repair in Palm City. We chart 240-volt heating elements, thermal cutoffs, high-limit thermostats, centrifugal motor switches, and Florida attic exhaust restrictions on the truck — call (772) 501-9870 to dispatch.
Call directly or submit the request form below for same-day dispatch. We cover all of Palm City including rural western stretches. Share cross streets when booking so routing is efficient. The diagnostic fee and warranty terms match the rest of the Treasure Coast route. $75 diagnostic, credited 100% toward approved same-visit repair.
Live Dispatch Radar
Live coverage across Tradition, St. Lucie West, Sandpiper Bay, and the greater Treasure Coast — track Mobile Unit #1 and confirm your ZIP before you request service.
Live unit status
Mobile Unit #1 — Dispatched
Current area: Port St. Lucie
⚡ Status: Dispatched & On Call
Pan the radar to your neighborhood (34953, 34986, 34983…).
🚐 Mobile Unit #1 · Port St. Lucie
Local conditions
Symptom, local cause, and how we test — each card stays short for mobile scanning.
Palm City LG dryers die from wet lint in hot attic runs. Garage laundry in Palm City proper shortens elements, thermal cutoffs, and high-limit thermostats.
In Palm City, estuary humidity and periodic salt-tinged air cakes wet lint in attic exhaust runs and seizes exterior flappers. A no-heat LG dryer is a 240-volt element, thermal-cutoff, and high-limit path until that duct is proven.
Lightning on older rural services west of Martin Highway opens LG thermal cutoffs and chatters centrifugal-switch contacts. A no-heat dryer after a storm is a high-limit and 240-volt element path, not a new heater by default.
Common failures
d80 · d90
LG sensor-dry platforms throw d80 / d90 when the exhaust cannot reject moisture. Treasure Coast houses stack long flexible runs through hot attics; humidity wets the lint and the blower loads up.
Element / igniter / thermal fuse
Electric models get element and fuse continuity; gas units get igniter amp draw. Replacing the heater without clearing a 40-foot soffit run returns the same call in three weeks.
Belt / idler / door switch
A silent drum with a humming motor is usually a broken belt or seized idler — not the timer.
Field diagnostics
LG dryer heat starts at the thermistor harness and the exhaust. Heat-pump models get an exchanger clean before any compressor talk.
Platform: Sensor-dry / dual thermistor
| Component | Test | Spec / pass line |
|---|---|---|
| Exhaust thermistor (TE2 / TE3 class) | Ohms versus the LG chart at the control harness | An open circuit at the harness is often the pin, not the thermistor bead |
Interactive bench check
Ohm, kΩ, µF, or voltage — not an error-code lookup. Pick the component, enter what the meter shows, and we will tell you whether the control board is being lied to.
Compressor or motor start capacitor. Example 108 µF nameplate ±10% (97–119 µF). Always compare to the can — a 35 µF motor cap is a different window
Capacitors store a shock. Short the terminals with an insulated screwdriver after unplugging. Do not use the ohm range as a substitute for a µF meter.
Enter the meter reading
Spec: Example 108 µF nameplate ±10% (97–119 µF). Always compare to the can — a 35 µF motor cap is a different window
Lint on the heat exchanger looks like a failed compressor. We clean and measure ΔT before sealed-system language.
Keep / repair: Drum bearings are quiet and the job is element, cutoff, gas valve coils, or a seized exterior flapper
Replace when: Blower wheel melted, drum support failed, or a heat-pump dryer whose exchanger and compressor quote exceeds half of replacement
Hyper-local conditions
Palm City is well water and older electrical. Slow ice is an inlet screen until proven otherwise. Dead 240 V appliances get a panel check. Hidden Oaks and Citrus Boulevard are extended coverage — the ticket carries a window, not a 'be there in an hour' promise. For LG dryers here: Water chemistry matters less than exhaust: wet lint and a seized flapper keep cutting heat after a new element. Ice-maker fill valves clog with grit; washer screens load rust-tinged debris; dishwashers scale faster than any county-fed Stuart kitchen. Access: Share the cross street and whether the lot is well or county water. We confirm a defined arrival window so a western lot is not treated like Sandpiper Bay.
Private wells west of Martin Highway and toward Citrus Boulevard, plus some county-fed pockets closer to Stuart
Harder, iron-heavier, and dirtier than coastal Martin municipal water — this is sediment, not a light scale film
Ice-maker fill valves clog with grit; washer screens load rust-tinged debris; dishwashers scale faster than any county-fed Stuart kitchen
River-adjacent humidity on the east lots, inland heat on the acreage — milder salt than Jensen Beach
Older 100–200 A services on larger lots were not sized for today’s 240 V dryers and ranges
A 'dead' dryer or oven is a breaker or a loose lug as often as an internal part; door-boot mold still happens on the river side
Hidden Oaks, Citrus Boulevard acreage, Martin Highway corridor
Extended-route window — not an instant same-day hop from the Port St. Lucie shop. Gated Hidden Oaks needs the approved entrance
Share the cross street and whether the lot is well or county water. We confirm a defined arrival window so a western lot is not treated like Sandpiper Bay
On this stop
In Palm City we treat LG dryers as a Sensor-dry / dual thermistor job, not a generic appliance call. First meter check: Exhaust thermistor (TE2 / TE3 class) — Ohms versus the LG chart at the control harness (An open circuit at the harness is often the pin, not the thermistor bead). Heat-pump LG dryers are exchanger hygiene first: Lint on the heat exchanger looks like a failed compressor. We clean and measure ΔT before sealed-system language. Local water is Private wells west of Martin Highway and toward Citrus Boulevard, plus some county-fed pockets closer to Stuart. Harder, iron-heavier, and dirtier than coastal Martin municipal water — this is sediment, not a light scale film. Install reality: Older 100–200 A services on larger lots were not sized for today’s 240 V dryers and ranges A 'dead' dryer or oven is a breaker or a loose lug as often as an internal part; door-boot mold still happens on the river side. Triage on this platform (10–14 years if the vent is maintained): repair when Drum bearings are quiet and the job is element, cutoff, gas valve coils, or a seized exterior flapper Replace when Blower wheel melted, drum support failed, or a heat-pump dryer whose exchanger and compressor quote exceeds half of replacement.
Field dispatch
Structured truck notes — symptom, meter path, parts. Not a star rating.
Verified local repair · Martin Highway lot, 100 A original service
Verified local repair · appliance was never the failed part
Verified local repair · Village Parkway townhome, closet exhaust into a wet soffit
Verified local repair · cycle time back in spec
LG dryer coverage in Palm City runs Martin Highway, Citrus Boulevard, and Hidden Oaks as an extended Martin County corridor. We confirm a defined window so a rural-lot stop is not treated as an instant same-day hop from the Port St. Lucie hub.
View our full range of Palm City appliance repair services, or explore our dedicated diagnostic hubs for dryer repair and LG appliance repair. For official municipal context, see the Martin County government website. Advertised coverage stays inside Port St. Lucie, Tradition, St. Lucie West, Torino, PGA Village, Jensen Beach, Stuart, Fort Pierce, White City, Hutchinson Island, Palm City, and Lakewood Park — we do not book Hobe Sound or Vero Beach from these pages.
FAQ · Pay on-site
No. No online prepayment — pay on-site upon diagnostic/approval. The in-home diagnostic is $75, credited 100% toward an approved repair on the same visit. A second appliance on the same stop is $35.
We schedule confirmed arrival windows throughout Palm City and surrounding neighborhoods, particularly for calls received before 2:00 PM. Our dispatch team coordinates directly with you to provide a tight arrival window.
Port St. Lucie Appliance Repair holds a 4.7/5 aggregate rating from 348+ Treasure Coast customer reviews.
Live Google reviews
Pulled from our Google Business Profile (4.7/5 from 348+ Verified Reviews). If Google is briefly unavailable, we show recent local feedback instead — same shop, same number (772) 501-9870.
Quick facts for customers and assistants: 4.7/5 from 348+ reviews · $75.00 diagnostic (credited) · 90-day warranty · serving Tradition, St. Lucie West, Stuart & Port St. Lucie.