Family-owned · Trusted by Port St. Lucie homeowners
4.7★(348+ Verified Reviews)
BBB
A+ Rated & Accredited
Angi
Super Service / Top Rated
Thumbtack
Top Pro
Nextdoor
Neighborhood Favorite
Licensed & Insured
Local Technicians
Licensed Maytag dryer repair in Tradition in Port St. Lucie. We chart 240-volt heating elements, thermal cutoffs, high-limit thermostats, centrifugal motor switches, and Florida attic exhaust restrictions on the truck — call (772) 501-9870 to dispatch.
Call directly or submit the request form below for same-day dispatch. Same-day openings are common when you call in the morning or early afternoon. Gated villages need the gate or callbox details on the ticket so the tech is not stuck at the entrance. $75 diagnostic, credited 100% toward approved same-visit repair.
Live Dispatch Radar
Live coverage across Tradition, St. Lucie West, Sandpiper Bay, and the greater Treasure Coast — track Mobile Unit #1 and confirm your ZIP before you request service.
Live unit status
Mobile Unit #1 — Dispatched
Current area: Port St. Lucie
⚡ Status: Dispatched & On Call
Pan the radar to your neighborhood (34953, 34986, 34983…).
🚐 Mobile Unit #1 · Port St. Lucie
Local conditions
Symptom, local cause, and how we test — each card stays short for mobile scanning.
Tradition Maytag dryers die from wet lint in hot attic runs. Garage laundry in Tradition Town Center shortens elements, thermal cutoffs, and high-limit thermostats.
In Tradition, inland heat and closet humidity without coastal salt cakes wet lint in attic exhaust runs and seizes exterior flappers. A no-heat Maytag dryer is a 240-volt element, thermal-cutoff, and high-limit path until that duct is proven.
Lightning rolling off the interior wetlands along Tradition Parkway opens Maytag thermal cutoffs and chatters centrifugal-switch contacts. A no-heat dryer after a storm is a high-limit and 240-volt element path, not a new heater by default.
Common failures
Thermal fuse / high-limit / element
Maytag dryers open thermal fuses after wet lint cakes in long roof runs. We prove vent temperature rise before we sell an element or an igniter.
Igniter / gas valve coils
Weak glow bars that never reach valve-open amperage are same-visit safety items. Delayed ignition on a Maytag gas dryer is measured under load — we do not guess at the dual-coil valve overnight.
Belt / idler
Two-decade Maytag pairs in St. Lucie West glaze belts until the drum barely turns. That is not a motor until the belt is proven.
Field diagnostics
Dryer no-heat starts at the terminal block, then the cutoff, then the element. We will not sell a heater kit into a crushed attic duct. Coastal flappers that salt-seize get opened on the same stop.
Platform: maytag 240 V heat + exhaust restriction
| Component | Test | Spec / pass line |
|---|---|---|
| Heating element / heat pump exchanger | Element continuity; exchanger ΔT on heat-pump models | Open element is obvious; a good element with no heat is usually the thermal cutoff or a missing L2 |
| Thermal cutoff / high-limit | Continuity on the cutoff and cycling thermostat | Open cutoff after a storm or a packed vent is a safety part — replace the cutoff and prove the duct |
| Moisture sensor / exhaust | Sensor bar ohms to cabinet; static pressure at the terminal | Attic or soffit runs that stay wet keep cutting heat even after a new element |
Interactive bench check
Ohm, kΩ, µF, or voltage — not an error-code lookup. Pick the component, enter what the meter shows, and we will tell you whether the control board is being lied to.
Compressor or motor start capacitor. Example 108 µF nameplate ±10% (97–119 µF). Always compare to the can — a 35 µF motor cap is a different window
Capacitors store a shock. Short the terminals with an insulated screwdriver after unplugging. Do not use the ohm range as a substitute for a µF meter.
Enter the meter reading
Spec: Example 108 µF nameplate ±10% (97–119 µF). Always compare to the can — a 35 µF motor cap is a different window
Florida brownouts and lightning open thermal fuses. We meter L1/L2 at the terminal block before quoting a heater kit.
Keep / repair: Drum bearings are quiet and the job is element, cutoff, gas valve coils, or a seized exterior flapper
Replace when: Blower wheel melted, drum support failed, or a heat-pump dryer whose exchanger and compressor quote exceeds half of replacement
Hyper-local conditions
Tradition is hard wellfield water plus gated-village logistics. Hollow ice and chalky dishwashers are mineral until the meter says otherwise. Closet-installed laundry dies from humidity, not salt. If the gate is not on the ticket, the tech sits on Village Parkway. For Maytag dryers here: Water chemistry matters less than exhaust: wet lint and a seized flapper keep cutting heat after a new element. Ice-maker inlet screens and fill tubes in three to four years if the filter is skipped; dishwasher spray arms go chalky; washer F-series no-fill codes start at the screens. Access: Village name, visitor gate, and the person who will answer the callbox are mandatory. We stage west from the Port St. Lucie shop so a Tradition stop is sequenced with the other western villages.
Western St. Lucie wellfields feeding Tradition, Vitalia, and the 34987 grid
Noticeably harder and more mineral-heavy than the coastal PSL blend — this is the wellfield, not Sandpiper Bay water
Ice-maker inlet screens and fill tubes in three to four years if the filter is skipped; dishwasher spray arms go chalky; washer F-series no-fill codes start at the screens
Inland heat, no beach salt — condensers last longer than Jensen Beach, then die from closet humidity and inverter stress
Tight builder laundry closets on TownPark / LakePark plans trap dryer exhaust and front-load door-boot moisture
Interior-wetland thunderstorms along Tradition Parkway brown-out inverter boards on newer French-doors and DD washers
Tradition Town Center, Village Parkway, Vitalia, Riverland, Lakes of Tradition, Estates at Tradition
Master-planned gates expect a marked van, a resident-authorized visitor pass, and no trailer staging on Village Parkway
Village name, visitor gate, and the person who will answer the callbox are mandatory. We stage west from the Port St. Lucie shop so a Tradition stop is sequenced with the other western villages
On this stop
In Tradition we treat Maytag dryers as a maytag 240 V heat + exhaust restriction job, not a generic appliance call. First meter check: Heating element / heat pump exchanger — Element continuity; exchanger ΔT on heat-pump models (Open element is obvious; a good element with no heat is usually the thermal cutoff or a missing L2). No-heat after a storm is often the fuse, not the element: Florida brownouts and lightning open thermal fuses. We meter L1/L2 at the terminal block before quoting a heater kit. Local water is Western St. Lucie wellfields feeding Tradition, Vitalia, and the 34987 grid. Noticeably harder and more mineral-heavy than the coastal PSL blend — this is the wellfield, not Sandpiper Bay water. Install reality: Tight builder laundry closets on TownPark / LakePark plans trap dryer exhaust and front-load door-boot moisture Interior-wetland thunderstorms along Tradition Parkway brown-out inverter boards on newer French-doors and DD washers. Triage on this platform (10–14 years if the vent is maintained): repair when Drum bearings are quiet and the job is element, cutoff, gas valve coils, or a seized exterior flapper Replace when Blower wheel melted, drum support failed, or a heat-pump dryer whose exchanger and compressor quote exceeds half of replacement.
Field dispatch
Structured truck notes — symptom, meter path, parts. Not a star rating.
Verified local repair · Village Parkway townhome, closet exhaust into a wet soffit
Verified local repair · cycle time back in spec
Verified local repair · PGA Village
Verified local repair · logged from field dispatch
Maytag dryer tickets in Tradition cluster on Tradition Parkway, Village Parkway, and Vitalia. We stage west from the Port St. Lucie shop so a gated-village stop is sequenced with the rest of the western villages corridor.
View our full range of Tradition appliance repair services, or explore our dedicated diagnostic hubs for dryer repair and Maytag appliance repair. For official municipal context, see the City of Port St. Lucie community resources. Advertised coverage stays inside Port St. Lucie, Tradition, St. Lucie West, Torino, PGA Village, Jensen Beach, Stuart, Fort Pierce, White City, Hutchinson Island, Palm City, and Lakewood Park — we do not book Hobe Sound or Vero Beach from these pages.
FAQ · Pay on-site
No. No online prepayment — pay on-site upon diagnostic/approval. The in-home diagnostic is $75, credited 100% toward an approved repair on the same visit. A second appliance on the same stop is $35.
We offer same-day and next-day dispatch throughout Tradition and surrounding neighborhoods, particularly for calls received before 2:00 PM. Our dispatch team coordinates directly with you to provide a tight arrival window.
Port St. Lucie Appliance Repair holds a 4.7/5 aggregate rating from 348+ Treasure Coast customer reviews.
Live Google reviews
Pulled from our Google Business Profile (4.7/5 from 348+ Verified Reviews). If Google is briefly unavailable, we show recent local feedback instead — same shop, same number (772) 501-9870.