Family-owned · Trusted by Port St. Lucie homeowners
4.7★(348+ Verified Reviews)
BBB
A+ Rated & Accredited
Angi
Super Service / Top Rated
Thumbtack
Top Pro
Nextdoor
Neighborhood Favorite
Licensed & Insured
Local Technicians
Licensed GE dryer repair in Stuart. We chart 240-volt heating elements, thermal cutoffs, high-limit thermostats, centrifugal motor switches, and Florida attic exhaust restrictions on the truck — call (772) 501-9870 to dispatch.
Call directly or submit the request form below for same-day dispatch. Same-day openings are common when you call in the morning. Stuart is a core part of the regular Treasure Coast route from the Port St. Lucie hub. $75 diagnostic, credited 100% toward approved same-visit repair.
Live Dispatch Radar
Live coverage across Tradition, St. Lucie West, Sandpiper Bay, and the greater Treasure Coast — track Mobile Unit #1 and confirm your ZIP before you request service.
Live unit status
Mobile Unit #1 — Dispatched
Current area: Port St. Lucie
⚡ Status: Dispatched & On Call
Pan the radar to your neighborhood (34953, 34986, 34983…).
🚐 Mobile Unit #1 · Port St. Lucie
Local conditions
Symptom, local cause, and how we test — each card stays short for mobile scanning.
Stuart GE dryers die from wet lint in hot attic runs. Garage laundry in Downtown Stuart shortens elements, thermal cutoffs, and high-limit thermostats.
In Stuart, estuary humidity and periodic salt-tinged air cakes wet lint in attic exhaust runs and seizes exterior flappers. A no-heat GE dryer is a 240-volt element, thermal-cutoff, and high-limit path until that duct is proven.
Lightning along the Roosevelt Bridge and Kanner Highway storm corridor opens GE thermal cutoffs and chatters centrifugal-switch contacts. A no-heat dryer after a storm is a high-limit and 240-volt element path, not a new heater by default.
Common failures
Moisture sensor bars / cycling thermostat
GE moisture-sensor bars filmed with fabric softener fake “already dry” on long cycles. We clean or replace the bars after proving the vent.
Terminal block / element / igniter
Electric dryers need a healthy 240-volt pair. Older Palm City and White City panels are worth checking before internal parts.
Blower wheel / motor
Packed blower wheels throw the motor off balance and trip cycling thermostats that look like a failed heater. We pull the wheel and transition duct before quoting an element.
Field diagnostics
GE dryer heat starts at the terminal-block lugs, then the cutoff, then the element. A 00/01 moisture code is the sensor bars until they ohm clean.
Platform: Moisture-sensor bar + 240 V heat
| Component | Test | Spec / pass line |
|---|---|---|
| 00 / 01 moisture sensor | Bar-to-cabinet ohms after cleaning | A 00/01 code with coated bars is a cleaning, not a new control |
Interactive bench check
Ohm, kΩ, µF, or voltage — not an error-code lookup. Pick the component, enter what the meter shows, and we will tell you whether the control board is being lied to.
Compressor or motor start capacitor. Example 108 µF nameplate ±10% (97–119 µF). Always compare to the can — a 35 µF motor cap is a different window
Capacitors store a shock. Short the terminals with an insulated screwdriver after unplugging. Do not use the ohm range as a substitute for a µF meter.
Enter the meter reading
Spec: Example 108 µF nameplate ±10% (97–119 µF). Always compare to the can — a 35 µF motor cap is a different window
GE dryers melt the L2 lug at the terminal block. We inspect the crimp before an element kit.
Keep / repair: Drum bearings are quiet and the job is element, cutoff, gas valve coils, or a seized exterior flapper
Replace when: Blower wheel melted, drum support failed, or a heat-pump dryer whose exchanger and compressor quote exceeds half of replacement
Hyper-local conditions
Stuart is Martin County municipal water and river humidity. We pull the coil on every garage fridge near the Roosevelt Bridge before a sealed-system sentence. Storm-dead dryers get a fuse check. North River Shores tickets need the bridge note or the van does not fit. For GE dryers here: Water chemistry matters less than exhaust: wet lint and a seized flapper keep cutting heat after a new element. Dishwasher Calrod heaters and washer inlet screens on river-side homes; ice valves clog later than in Tradition but sooner than a brand-new PSL east-side install. Access: Port Salerno is booked as Stuart (34997), not a separate city. Downtown alleys and river-side driveways need a place to leave the van that is not blocking a cafe lot.
City of Stuart municipal supply — moderate hardness, not Palm City well sediment and not Tradition wellfield calcium
Slow mineral load that shows up on original equipment in downtown and East Stuart houses, not overnight scale
Dishwasher Calrod heaters and washer inlet screens on river-side homes; ice valves clog later than in Tradition but sooner than a brand-new PSL east-side install
St. Lucie River estuary humidity — downtown, North River Shores, and the Roosevelt Bridge corridor, not just the 'waterfront lot'
Garage and carport refrigerators near the river pick up the coastal Martin corrosion pattern without being on A1A
Storm corridor welds oven and washer boards; a dryer that dies after a cell is almost always the thermal fuse
Downtown Stuart, East Stuart, North River Shores, Port Salerno, Kanner Highway subdivisions
North River Shores private bridges have posted weight limits — we note them before sending a stocked van
Port Salerno is booked as Stuart (34997), not a separate city. Downtown alleys and river-side driveways need a place to leave the van that is not blocking a cafe lot
On this stop
In Stuart we treat GE dryers as a Moisture-sensor bar + 240 V heat job, not a generic appliance call. First meter check: 00 / 01 moisture sensor — Bar-to-cabinet ohms after cleaning (A 00/01 code with coated bars is a cleaning, not a new control). No heat that is the terminal block: GE dryers melt the L2 lug at the terminal block. We inspect the crimp before an element kit. Local water is City of Stuart municipal supply — moderate hardness, not Palm City well sediment and not Tradition wellfield calcium. Slow mineral load that shows up on original equipment in downtown and East Stuart houses, not overnight scale. Install reality: Garage and carport refrigerators near the river pick up the coastal Martin corrosion pattern without being on A1A Storm corridor welds oven and washer boards; a dryer that dies after a cell is almost always the thermal fuse. Triage on this platform (10–14 years if the vent is maintained): repair when Drum bearings are quiet and the job is element, cutoff, gas valve coils, or a seized exterior flapper Replace when Blower wheel melted, drum support failed, or a heat-pump dryer whose exchanger and compressor quote exceeds half of replacement.
Field dispatch
Structured truck notes — symptom, meter path, parts. Not a star rating.
Verified local repair · Kanner Highway after an afternoon cell
Verified local repair · no element kit
Verified local repair · Becker Road corridor after a storm cell
Verified local repair · heat restored, cutoff will not be repeated into a wet duct
GE dryer calls in Stuart follow US-1, Kanner Highway, and the Roosevelt Bridge corridor, then Port Salerno and East Stuart when the window allows a downtown grouping.
View our full range of Stuart appliance repair services, or explore our dedicated diagnostic hubs for dryer repair and GE appliance repair. For official municipal context, see the City of Stuart official website. Advertised coverage stays inside Port St. Lucie, Tradition, St. Lucie West, Torino, PGA Village, Jensen Beach, Stuart, Fort Pierce, White City, Hutchinson Island, Palm City, and Lakewood Park — we do not book Hobe Sound or Vero Beach from these pages.
FAQ · Pay on-site
No. No online prepayment — pay on-site upon diagnostic/approval. The in-home diagnostic is $75, credited 100% toward an approved repair on the same visit. A second appliance on the same stop is $35.
We offer same-day and next-day dispatch throughout Stuart and surrounding neighborhoods, particularly for calls received before 2:00 PM. Our dispatch team coordinates directly with you to provide a tight arrival window.
Port St. Lucie Appliance Repair holds a 4.7/5 aggregate rating from 348+ Treasure Coast customer reviews.
Live Google reviews
Pulled from our Google Business Profile (4.7/5 from 348+ Verified Reviews). If Google is briefly unavailable, we show recent local feedback instead — same shop, same number (772) 501-9870.
Quick facts for customers and assistants: 4.7/5 from 348+ reviews · $75.00 diagnostic (credited) · 90-day warranty · serving Tradition, St. Lucie West, Stuart & Port St. Lucie.