Family-owned · Trusted by Port St. Lucie homeowners
4.7★(348+ Verified Reviews)
BBB
A+ Rated & Accredited
Angi
Super Service / Top Rated
Thumbtack
Top Pro
Nextdoor
Neighborhood Favorite
Licensed & Insured
Local Technicians
Licensed GE dryer repair in Jensen Beach. We chart 240-volt heating elements, thermal cutoffs, high-limit thermostats, centrifugal motor switches, and Florida attic exhaust restrictions on the truck — call (772) 501-9870 to dispatch.
Call directly or submit the request form below for same-day dispatch. Same-day openings are common when you call in the morning. Coastal coil cleaning is part of refrigeration calls near the water, not an upsell. $75 diagnostic, credited 100% toward approved same-visit repair.
Live Dispatch Radar
Live coverage across Tradition, St. Lucie West, Sandpiper Bay, and the greater Treasure Coast — track Mobile Unit #1 and confirm your ZIP before you request service.
Live unit status
Mobile Unit #1 — Dispatched
Current area: Port St. Lucie
⚡ Status: Dispatched & On Call
Pan the radar to your neighborhood (34953, 34986, 34983…).
🚐 Mobile Unit #1 · Port St. Lucie
Local conditions
Symptom, local cause, and how we test — each card stays short for mobile scanning.
Jensen Beach GE dryer vents salt-seize at the flapper. We inspect that hinge and the attic run before selling a 240-volt heater or igniter.
In Jensen Beach, direct salt-air and lagoon humidity cakes wet lint in attic exhaust runs and seizes exterior flappers. A no-heat GE dryer is a 240-volt element, thermal-cutoff, and high-limit path until that duct is proven.
Lightning this close to the Indian River Lagoon opens GE thermal cutoffs and chatters centrifugal-switch contacts. A no-heat dryer after a storm is a high-limit and 240-volt element path, not a new heater by default.
Common failures
Moisture sensor bars / cycling thermostat
GE moisture-sensor bars filmed with fabric softener fake “already dry” on long cycles. We clean or replace the bars after proving the vent.
Terminal block / element / igniter
Electric dryers need a healthy 240-volt pair. Older Palm City and White City panels are worth checking before internal parts.
Blower wheel / motor
Packed blower wheels throw the motor off balance and trip cycling thermostats that look like a failed heater. We pull the wheel and transition duct before quoting an element.
Field diagnostics
GE dryer heat starts at the terminal-block lugs, then the cutoff, then the element. A 00/01 moisture code is the sensor bars until they ohm clean.
Platform: Moisture-sensor bar + 240 V heat
| Component | Test | Spec / pass line |
|---|---|---|
| 00 / 01 moisture sensor | Bar-to-cabinet ohms after cleaning | A 00/01 code with coated bars is a cleaning, not a new control |
Interactive bench check
Ohm, kΩ, µF, or voltage — not an error-code lookup. Pick the component, enter what the meter shows, and we will tell you whether the control board is being lied to.
Compressor or motor start capacitor. Example 108 µF nameplate ±10% (97–119 µF). Always compare to the can — a 35 µF motor cap is a different window
Capacitors store a shock. Short the terminals with an insulated screwdriver after unplugging. Do not use the ohm range as a substitute for a µF meter.
Enter the meter reading
Spec: Example 108 µF nameplate ±10% (97–119 µF). Always compare to the can — a 35 µF motor cap is a different window
GE dryers melt the L2 lug at the terminal block. We inspect the crimp before an element kit.
Keep / repair: Drum bearings are quiet and the job is element, cutoff, gas valve coils, or a seized exterior flapper
Replace when: Blower wheel melted, drum support failed, or a heat-pump dryer whose exchanger and compressor quote exceeds half of replacement
Hyper-local conditions
Jensen Beach is salt first. A warm refrigerator on A1A is a coil until the fins are proven. Well-side Rio lots add iron grit that A1A condos never see. Country Club stops need the guardhouse name on the ticket; island jobs are a different schedule. For GE dryers here: Water chemistry matters less than exhaust: wet lint and a seized flapper keep cutting heat after a new element. Ice-maker and dishwasher valves need both scale and grit checks; Rio wells stain washer screens orange, municipal A1A blocks do not. Access: Rio addresses need a cross street — Indian River Drive numbers are easy to overrun. Hutchinson Island stays on the separate island window, not this ticket.
Mix of municipal A1A / Ocean Boulevard blocks and older well-influenced properties on Indian River Drive and Rio
Well-side iron and sediment on the lagoon lots; softer city water a few blocks inland — two different inlet-valve failures on the same street
Ice-maker and dishwasher valves need both scale and grit checks; Rio wells stain washer screens orange, municipal A1A blocks do not
Direct salt air — the single harshest advertised stop. A1A, the causeway, and lagoon-front Indian River Drive
Garage refrigerators within a half-mile of the water pit aluminum fins; dryer terminals facing the lagoon salt-seize at the flapper hinge
Compressor overwork from a packed, pitted coil; front-load door boots mold inside the fold within a year or two; hurricane-season board resets
Indian River Drive / Rio, Jensen Beach Causeway approach, Jensen Beach Country Club / Eagle Marsh, Ocean Boulevard condos
Country Club guardhouse wants contractor ID and a resident call-ahead. Condo decks often ban overnight commercial parking
Rio addresses need a cross street — Indian River Drive numbers are easy to overrun. Hutchinson Island stays on the separate island window, not this ticket
On this stop
In Jensen Beach we treat GE dryers as a Moisture-sensor bar + 240 V heat job, not a generic appliance call. First meter check: 00 / 01 moisture sensor — Bar-to-cabinet ohms after cleaning (A 00/01 code with coated bars is a cleaning, not a new control). No heat that is the terminal block: GE dryers melt the L2 lug at the terminal block. We inspect the crimp before an element kit. Local water is Mix of municipal A1A / Ocean Boulevard blocks and older well-influenced properties on Indian River Drive and Rio. Well-side iron and sediment on the lagoon lots; softer city water a few blocks inland — two different inlet-valve failures on the same street. Install reality: Garage refrigerators within a half-mile of the water pit aluminum fins; dryer terminals facing the lagoon salt-seize at the flapper hinge Compressor overwork from a packed, pitted coil; front-load door boots mold inside the fold within a year or two; hurricane-season board resets. Triage on this platform (10–14 years if the vent is maintained): repair when Drum bearings are quiet and the job is element, cutoff, gas valve coils, or a seized exterior flapper Replace when Blower wheel melted, drum support failed, or a heat-pump dryer whose exchanger and compressor quote exceeds half of replacement.
Field dispatch
Structured truck notes — symptom, meter path, parts. Not a star rating.
Verified local repair · Causeway-facing terminal
Verified local repair · heat and exhaust both proven
Verified local repair · Becker Road corridor after a storm cell
Verified local repair · heat restored, cutoff will not be repeated into a wet duct
GE dryer routing in Jensen Beach hugs Indian River Drive, the causeway, and A1A / Ocean Boulevard. Coastal stops are grouped so we are not crossing the lagoon twice in one arrival window.
View our full range of Jensen Beach appliance repair services, or explore our dedicated diagnostic hubs for dryer repair and GE appliance repair. For official municipal context, see the Martin County government website. Advertised coverage stays inside Port St. Lucie, Tradition, St. Lucie West, Torino, PGA Village, Jensen Beach, Stuart, Fort Pierce, White City, Hutchinson Island, Palm City, and Lakewood Park — we do not book Hobe Sound or Vero Beach from these pages.
FAQ · Pay on-site
No. No online prepayment — pay on-site upon diagnostic/approval. The in-home diagnostic is $75, credited 100% toward an approved repair on the same visit. A second appliance on the same stop is $35.
We offer same-day and next-day dispatch throughout Jensen Beach and surrounding neighborhoods, particularly for calls received before 2:00 PM. Our dispatch team coordinates directly with you to provide a tight arrival window.
Port St. Lucie Appliance Repair holds a 4.7/5 aggregate rating from 348+ Treasure Coast customer reviews.
Live Google reviews
Pulled from our Google Business Profile (4.7/5 from 348+ Verified Reviews). If Google is briefly unavailable, we show recent local feedback instead — same shop, same number (772) 501-9870.
Quick facts for customers and assistants: 4.7/5 from 348+ reviews · $75.00 diagnostic (credited) · 90-day warranty · serving Tradition, St. Lucie West, Stuart & Port St. Lucie.